Surface-mounted box for the controllers RT-03, RT-08, RT-12 with a plastic cover frame.

Double flush-mounted box   Ø 62/48. It's dedicated for the following controllers: RT-08K, RT-03B, RT-03C, RT-08S

Deep single flush-mounted box   Ø 62/60. It's dedicated for the RT-10 controller

Deep double flush-mounted box   Ø 62/60. It's dedicated for the following controllers: RT-08G, RT-08P, RT-08OS, RT-08OSG and RT-08OMG

The GAZEX detector is designed for a continuous monitoring of carbon monoxide in areas at risk of emission of this gas. The control is based on a cyclical measurement of CO concentration in the ambient air. After exceeding a determined value of CO and a determined time of exposure the alarm signalling of the detector is switched on.  The alarm is turned on at a concentration over  0.005% of CO after an exposure time of over 60 minutes or at a concentration of 0.01% after 10 min or at a concentration of 0.03% within 3 min. (in accordance with European standard EN 50291) The detector can work with stove controllers  of the company TATAREK.

The mounting kit of the BELIMO TF230 servomotor  is  a kit for mounting the Belimo TF230 servomotor. The kit  mounts it stable in a flat or side position, providing a full transfer of power of the servomotor to the chimney flap.For the mentioned kit it is necessary to buy a power transmission rod of a diameter of 6 mm and any length depending on the installation place of the servomotor. This servomotor has been selected after extensive tests and provides the appropriate force necessary for running the operation of the chimney flap at all times (even when the impurities gather). It has the return spring that gets the flap back to its original position if a power failure occurs, which is the location that guarantees complete safety of the system.

The BELIMO TF230 servomotor  is used to drive the chimney flap and it's a device that combined with the controllers  RT-08 SAC, RT-08 OS and RT-08 OS GRAFIK ensures a fully automatic operation of heat storage systems also in conjunction with the cooperating water base. This servomotor has been selected after extensive tests and provides the appropriate force necessary for running the operation of the chimney flap at all times (even when the impurities gather). It has the return spring that gets the flap back to its original position if a power failure occurs, which is the location that guarantees complete safety of the system.

The RT-09 PID  controller is designed to operate automatic solid fuel boilers equipped with a retort (screw) fuel feeder, in which the temperature of the boiler is changed by altering the cycles of fuel feeding and smooth control of the air blower. The advanced "TATAREK PID" algorithm of the operation  enables the automatic modulation of the boiler power - so much heat is generated as you need. The combustion process is uniform (no sudden changes of temperature in the combustion chamber and the chimney), more efficient and ensures a longer life of the heating system.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-04 "ADAŚ" Version B is a controller adapted to operate central heating solid fuel boilers to stabilize the operation of the boiler by measuring the water temperature. This controller is a hybrid model of those offered so far, that is,  RT-04 ADAŚ and RT-01 ANIA version B, because the existing technical solutions have not been altered, while the housing itself has been changed to the same which is used in the controllers RT-01 and RT-02 versions B. This change was dictated by the demands of clients for whom the existing control panel was a bit cumbersome because of its size. Functionally, this controller performs the same tasks as in the previous model.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-02 "ANETA" - VERSION B is a controller adapted to operate central heating solid fuel boilers to stabilize the operation of the boiler by measuring the water temperature. It regulates the air blower, adjusts the operation of the circulating pump or pumps (see the parameter maximum connection power in the technical data), protects the central heating system against the boiling of water in the system. This controller combines the functions of a conventional controller for central heating solid fuel boilers and programmable thermostat, since it has built-in timer for automatically varying the temperature of the boiler in four selected times of the daily cycle.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-01 "ANIA" - VERSION B is a controller adapted to operate central heating solid fuel boilers to stabilize the operation of the boiler by measuring the water temperature. It regulates the air blower, adjusts the operation of the circulating pump, controls the HW  load pump and protects the central heating system against the boiling of water in the system. The controller  RT-01B ANIA  also performs the boiler scavenge (to remove excess of harmful gases produced in the combustion process) which, like the time intervals of the mentioned scavenges, the user can individually set depending on the type and grade of used fuel.

RT-10 - The rotation speed controller  RT-10 RO TITANIUM precisely and smoothly regulates the rotation of the different types of voltage controlled fans. The actuator is a triac. In the offer of the company TATAREK it‘s the simplest model that fills in a range of automatic controllers by that inexpensive product for less demanding customers. Indication of the rotation speed is presented on the control panel. The operation state (speed) is indicated by control lights. The increase in motor speed is indicated by the frequency of light impulses - from short to longer and longer, and in the final phase to continuous illumination. In the same way the increase in rotation speed registered by the fan is indicated up to the maximum level.

RT-03C - The microprocessor rotation speed controller RT-03C ARO measures temperature in the chamber of the stove inlet fan, determines its rotational speed and controls the flow of hot air. Regulation of the operation is made in two modes: manual or automatic one. In the manual mode, the speed of rotation is determined on a scale of 0 to 10. The temperature measurement doesn’t affect the change of the motor speed. In the automatic mode, the fan motor speed is adjusted automatically depending on temperature measurements. After the temperature exceeds 40 ° C, the fan switches to minimum speed. As the temperature rises the speed proportionally increases, reaching the maximum at 80 ° C. In the automatic mode, the controller display shows the current temperature readings.

RT-05 Jacuś - The automation system JACUŚ RT-05 is a multifunction 2-module device. The aesthetic control module [1] with the LCD display is to be mounted in any room where you will be making the most reliable measurement of internal temperature. The executive module [2], a small box containing a temperature sensor, you mount directly at the fan. RT-05 can be used as a controller of hot or cold air blow-in, enabling  manual or automatic selection of the fan speed ranging from 10 to 100%. RT-05 can also be used  as a controller of  room temperature. It found application in heating systems based on stoves with closed combustion chamber. The produced heat warms even a few rooms.

RT-08 SOLAR DUO - controller for solar systems with support for valves and loading pump of the storage tank or hot water buffer. It enables to automatically handle two valves and one loading pump of the hot water storage tank. It has three temperature sensors: 2 sensors for measuring the temperature of glycol in solar collectors and 1 sensor to measure water temperature in the buffer or the hot water storage tank.

RT-08 SOLAR TH - controller for solar systems with support for 2 pumps: the first one loading the buffer from solar collectors and the second one loading the hot water storage tank from the buffer. It has three temperature sensors: 1 sensor for measuring the temperature of glycol and 2 sensors to measure water temperature in the buffer (at 2 layers of the buffer).  Additionally it allows you to operate an electric heater to boost the heating of the buffer, and a clock with a zone thermostat which allows to maintain thermal comfort in different time zones of the daily cycle.

RT-08 SOLAR TL - The simplest controller to operate a solar collector that  transfers heat to the buffer. It allows you to operate one pump of the collector. It has two temperature sensors for measuring glycol and hot water in the buffer.

The microprocessor temperature controller RT-08 SOLAR is designed to operate heating systems, in which the heat source is the solar collector and water jacket stove. The control is based on the air damper while the receiver is the hot water storage tank (HW) and central heating (CH). Air damper control is done on a "on / off" base. This gives you the opportunity to use the dampers of various switch-on parameters.

TEMPERATURE CONTROLLER OF THE MIXING VALVE RT-12 is a device designed to smoothly control the servomotor of the 3-way valve in order to maintain temperature set by the user at its output. This controller is suited to operate all mixing valves that are equipped with a motor of the valve drive supplied with a AC voltage of 230V. The basic parameter determining the respective start of each function of the controller  here is a temperature sensor intended to be mounted to the heating pipe  coming out of the valve. The control functions are implemented through two outputs that are responsible for controlling the valve drive as well as an additional output that enables to operate the cooperating circulating pump.

The control kit of air supply to the stove by a IR-remote control. It allows the user to remotely control both the air damper that regulates air supply to the furnace and combustion process. The kit includes: IR-remote control, executive module mountable on the stove housing and air damper.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-08G  is a controller of the heating system, in which the heat source is the water jacket stove whose operation is controlled by the air damper controlling the combustion process. The primary function of the controller is to maintain the temperature in the water jacket at a preset level. That is carried out by the corresponding opening of the air damper that supplies air to the combustion chamber depending on the temperature measured in the water jacket. One of the basic functions of the controller is also maintaining a fully automatic operation of the 2 CH circulating pumps and the HW load pump whose work is regulated by temperature measurements made by two sensors in the HW  hot water storage tank.

RT-17 INTEGRATOR OF PUMP OPERATION - is the latest development of the company TATAREK, which was created in response to numerous inquiries from installers concerning this type of device. Integrator is a very simple and very efficient device with which it is possible to limit the number of pumps operating in the water system and thereby reduce the costs of its construction and operation. The main function of the integrator is a capability to use one circulating pump to supply  the water system, the operation of which is conditioned simultaneously by at least two sources of control. Thanks to this solution we can use one pump that can be  regulated both by a controller of a gas stove and a stove controller.

RT-08G BUFFER is a control kit with graphics display to operate the heating systems supplied by the water jacket stove, with adjustable air supply to the combustion chamber via the air damper. The controller provides both automatic operation of the loading pump of the hot water BUFFER and heat distribution through the circulating pump for the CH and the loading pump of the hot water system. It has three temperature water sensors. - 1 sensor to measure temperature in the water jacket, 1 buffer temperature sensor, and 1 sensor of the HW system.

The controller RT-08 OM GRAFIK / Optimizer of Stove Power /. This is a device intended for operating classic stove inserts and furnaces equipped with the air supply duct into the combustion chamber. The purpose of the controller is to optimize the operation of the furnace in terms of obtained power and stabilize its operation at the power range required by the user. This is done through the air damper that smoothly regulates the flow of air into the combustion chamber.

TEMPERATURE CONTROLLER OF THE CH PUMP TSP100 is a device intended to operate central heating circulating pumps or thermostatic valves working in heating systems. This controller allows you to operate those devices of a maximum connection power up to 500W. The whole regulation is based on temperature measurement carried out at any measuring point in a  range of 25ºC to 85ºC. It can operate in two modes, which are selected on the control panel via a switch. The first is the automatic mode (AUTO), which allows the fully automatic start and stop of the pump after exceeding the temperature set by the user. The temperature is selected with the knob conveniently located on the control panel of suitably calibrated temperature scale.

RT-08 OS GRAFIK (Optimizer of Combustion) - is the latest development of our company. The controller is designed to optimize the combustion process in conventional furnaces equipped with a direct flow of air into the combustion chamber.  By measuring  temperature directly over the combustion chamber, you achieve the most efficient regulation of the air supply, which combined with appropriate control algorithms allows to optimize the combustion process and thus a more economic use of the heat obtained in the process.

RT-08G BUFFER SOLAR is a control kit with graphics display to operate the heating systems supplied by the water jacket stove, with adjustable air supply to the combustion chamber via the air damper. The controller provides both automatic operation of the loading pump of the hot water BUFFER and heat distribution for the CH system. It can also operate solar collectors that supply the buffer. It has three temperature water sensors. - 1 sensor to measure temperature in the water jacket, 1 buffer temperature sensor, and 1 sensor of the solar system.

TEMPERATURE CONTROLLER OF THE CH PUMP TSP0-200 is a device intended to operate the load pumps of the HW storage tank or thermostatic valves working in heating systems. This controller allows you to operate those devices of a maximum connection power up to 500W. The whole regulation is based on temperature measurement carried out at any measuring point in a  range of 25ºC to 85ºC. It can operate in two modes, which are selected on the control panel via a switch. The first is the automatic mode (AUTO), which allows the fully automatic start and stop of the pump after exceeding the temperature set by the user.

RT-08 OS GRAFIK II(Optimizer of Combustion) - is the latest development of our company. The controller is designed to optimize the combustion process in conventional furnaces equipped with a direct flow of air into the combustion chamber.  By measuring  temperature directly over the combustion chamber, you achieve the most efficient regulation of the air supply, which combined with appropriate control algorithms allows to optimize the combustion process and thus a more economic use of the heat obtained in the process.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-08 P KOMINEK LUX  is the controller of the heating system, in which the heat source is the water jacket stove whose operation is controlled by the air damper controlling the combustion process. The primary function of the controller is to maintain the temperature in the water jacket at a preset level. That is carried out by the corresponding opening of the air damper that supplies air to the combustion chamber depending on the temperature measured in the water jacket. One of the basic functions of the controller is also maintaining a fully automatic operation of the 2 CH circulating pumps and the HW load pump whose work is regulated by temperature measurements made by two sensors in the HW  hot water storage tank.

MICROPROCESSOR TEMPERATURE CONTROLLER RT-08K "KOMINEK PLUS" is the latest product of the company TATAREK typically dedicated to operating complex heating systems supplied by stove inserts with water jacket and cooperating with the hot water storage tank (HW ). The basic function of the controller is a fully automatic operation of the 2 CH circulating pumps on the base of separate temperature settings for each of them and the HW  load pump whose work is regulated by temperature measurements made by two sensors in the HW  hot water tank. The controller  uses several innovations which are a further development of previously used and popular solution - RT-03 B Wojtuś.

RT SMART ROOM THERMOSTAT

The RT SMART room thermostat is designed to automatically regulate the temperature in the room by turning the boiler on and off. The thermostat has a relay output that gives an on / off signal when the set temperature is exceeded.

The device has the following functions:

The controller RT-08 OM / Optimizer of Stove Power /. This is a device intended for operating classic stove inserts and furnaces equipped with the air supply duct into the combustion chamber. The purpose of the controller is to optimize the operation of the furnace in terms of obtained power and stabilize its operation at the power range required by the user. This is done through the air damper that smoothly regulates the flow of air into the combustion chamber.

The RT-03 B temperature controller WOJTUŚ is used to control the operation of devices of the installations equipped with a water jacket stove as a main source of heating. It measures the temperature of the water jacket, and - depending on the preset parameters - controls the motor of the circulating pump and the electromagnetic valve. Optionally, you can connect the contact, which can operate an electrovalve, to the second circulating pump, which is increasingly being used more and more in heating systems. Both for the circulating pump and electromagnetic valve (possibly also for the second circulating pump), you can make individual temperature settings.

RT-08 OS (Optimizer of Combustion) - is the latest development of our company. The controller is designed to optimize the combustion process in conventional furnaces equipped with a direct flow of air into the combustion chamber.  By measuring  temperature directly over the combustion chamber, you achieve the most efficient regulation of the air supply, which combined with appropriate control algorithms allows to optimize the combustion process and thus a more economic use of the heat obtained in the process.

Subtotal4,41 zł
VAT 23%1,01 zł
Price5,42 zł




Subtotal3,59 zł
VAT 23%0,83 zł
Price4,42 zł




Subtotal9,44 zł
VAT 23%2,17 zł
Price11,61 zł




Subtotal4,32 zł
VAT 23%0,99 zł
Price5,31 zł




Subtotal9,44 zł
VAT 23%2,17 zł
Price11,61 zł




Subtotal4,20 zł
VAT 23%0,96 zł
Price5,16 zł




Subtotal4,20 zł
VAT 23%0,96 zł
Price5,16 zł




Subtotal3,89 zł
VAT 23%0,90 zł
Price4,79 zł




Subtotal9,44 zł
VAT 23%2,17 zł
Price11,61 zł




Subtotal12,82 zł
VAT 23%2,95 zł
Price15,77 zł




Description: 

Cable with separator TATAREK

Subtotal4,93 zł
VAT 23%1,13 zł
Price6,06 zł




Subtotal4,58 zł
VAT 23%1,05 zł
Price5,63 zł




Subtotal4,82 zł
VAT 23%1,11 zł
Price5,93 zł






On request housings are available in other colours and of other material.
Material: Bayblend; ABS
LVD according to  EN 60335-1:91; EN 60335-2-29